17 Homemade Chicken Pluckers You Can Build Right Now

LemonSlide is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

17 Homemade Chicken Pluckers You Can Build Right Now

Homemade Chicken Pluckers You Can Build Right Now

Plucking a chicken is easier said than done. After all, who wants to spend hours plucking a chicken!

The good news is that there is an easy way out. That is if you know how to build a chicken plucker.

Well, don’t worry a lot about the building part. There are many simple ideas for homemade chicken plucker you can implement.

Below, we look at 17 homemade chicken plucker plans you can put together at minimal cost.

You can find more than just these free homemade chicken plucker plans like plans for chicken feeder, homemade incubator, chicken waterer, chicken brooder, chicken coop, frame chicken coop, chicken tractor, pallet chicken coop, and many more.

Drill-Mounted Rotary Chicken Plucker

What the designer wants here is a low-cost, homemade chicken plucker. It needs to be a space-saver and easy to store.

He builds it using PVC cap, nuts, and straps. Of course, a power drill is needed to spin the pucker. The overall cost of this project is $16. This is the estimate in case you already have the power drill.

Holes are drilled on the cap. The straps fit through the holes in alternating rows of one and two. Here, the straps are used as fingers.

A hole is drilled at the center of the cap. This is where the chuck of the drill secures with a nut and washer.

The designer has put this plucking machine under test. So far, it performs accordingly and he’s happy with it!

2. 1-HP DIY Chicken Plucker

1-HP DIY Chicken Plucker

The DIYer behind this project dedicates herself to improving country lifestyle. She comes up with this motor-driven plucker. Her aim is to reduce the time and effort spend plucking chicken feathers.

The plucker is housed in a barrel and supported by a wooden frame. The bottom of the barrel is cut and holes drilled to fit rubber fingers. More holes are drilled on the sides of the barrel to fit more fingers.

The large number of fingers used here increase surface area, which reduces plucking time. The bottom of the barrel is reinforced and a pulley shaft fitted through.

“Cow Girl”, as the DIYer calls herself, has most materials on hand. She spends $49 on this project.

She’s happy with the end results. But she thinks of making an improvement. This is to include a collector that will catch the feathers.

3. 3/4 HP Drum Chicken Plucker

3/4 HP Drum Chicken Plucker

A Michigan farmer builds this DIY chicken plucking machine. His aim is to make a copy of a commercial plucker. The best part is that it takes only seconds to pluck one chicken.

Wooden boards, 12-inch PVC pipe, and rubber fingers are needed here. The PVC pipe is what makes the drum. Holes are drilled into it and fingers fitted.

The drum is mounted on a wooden stand. A pulley system connects it to the motor. This machine does not create a lot of mess by throwing feathers far. It just throws 5 to 6 feet away.

The farmer is happy that the machine performs well and has kept going for over 5 years now.

4. Mechanical Tub-Style Chicken Plucker for $200-$400

Mechanical Tub-Style Chicken Plucker for $200-$400

This machine makes chicken processing days less stressful. The designer wants a large homemade chicken plucking machine that handles many birds at a go.

This plucker is not only about size, but also efficiency. It reduces plucking time from minutes down to seconds. It sits on wheels so it is mobile.

The plucker is housed in a large 55-gallon barrel. A major part of the cost goes into purchasing the 80-100 fingers needed here.

A pulley connects the shaft at the bottom of the barrel to a 1/4 HP motor. This is what spins the drum. The designer says it performs well and can handle 10-15 birds at a go.

A similar machine out there fetches a price of $1,200, which makes this one a huge saving.

5. Upright Freestanding Chicken Plucker

Upright Freestanding Chicken Plucker

This is a YouTube project. The idea behind this project is to get a compact chicken plucker that doesn’t require external support.

The machine is built on a plywood frame. It is designed in the form of a drum chicken plucker using PVC pipe. 24 plucking fingers are needed in this project.

A pulley system driven by 1 HP compressor motor connects is what makes the drum spin. Bearings are fitted on the shaft to keep noise to a minimum.

6. Homemade Tub-Style Chicken Plucker with Plumping

Homemade Tub-Style Chicken Plucker with Plumping

Jason, a DIYer, builds this chicken plucking machine with the help of a friend. What he wants is a chicken plucker that operates like a time machine.

The plucker machine is housed inside a large barrel. A wooden frame supports the barrel, motor, and an electric switch. Once the plucker starts to spin, water is released from a valve to wash away the feathers.

Jason gives a pictorial illustration of each building step. This machine has been put to trial plucking 23 chickens. So far, it works great and only needs some few minor adjustments.

7. Two-Barrel Drill-Driven Chicken Plucker with Easy Pluck Kit

Two-Barrel Drill-Driven Chicken Plucker with Easy Pluck Kit

This is an imitation of the store-bought Easy Pluck machine. All parts are DIYed except for the roller. The designer uses Easy Pluck roller kit.

Buying the kit together with barrels cost a lot. So, the designer uses a clever plan by housing the kits in salvaged barrels.

The barrels are stacked. A cutout is made on the top barrel to fit the kit. The kit is spun using a power drill.

The bottom barrel has the top cut out. This is where feathers collect once plucked out. There is no littering your space with bird feathers.

8. Automatic Chicken Plucker from Air Compressor Motor

Automatic Chicken Plucker from Air Compressor Motor

David Nash builds this chicken plucker inspired by Whizbang plucking machines. His idea is to get the same design minus the expense.

So what he does is build it using salvaged materials. He uses wooden boards, three-phase air compressor motor, and PVC pipe. End caps fit both ends of the pipe. A hole is drilled through the caps to fit a shaft.

The pip has holes drilled to fit rubber fingers. The wooden frame supporting this plucker comes with a low-profile design. This makes it good to place on the kitchen countertop so you don’t bend a lot.

David comments this DIY chicken plucker. It has reduced chicken plucking time down to just a couple of minutes.

9. Washer Drum DIY Chicken Plucker

Washer Drum DIY Chicken Plucker

This is a YouTube video tutorial for a plucker that can be used for all poultry. In this project, the designer uses a large drum and motor.

The plucking fingers are fitted on the outer side of the drum. Therefore, feathers collect outside the drum. The result is easy cleaning of the drum.

The drum is installed in such a way that it sits side by side with the motor assembly. This means less obstruction and no need for a pulley.

10. $200 Chicken Plucker with Gearbox Drive

$200 Chicken Plucker with Gearbox Drive

I’d say this chicken plucker is built with durability and efficiency in mind. Durability is achieved through the gearbox system connected to 1/3 HP motor. The designer says it is more dependable compared to a pulley system.

The plucking fingers are fitted inside a barrel. This is to help contain the chicken and keep feathers from being thrown away. A splash guard is used here to keep your feet free from chicken soup.

The designer uses a wooden frame to support this plucker machine. It’s a fast machine that makes quick work of 17 birds in just 40 minutes. That is like two minutes spend in plucking one bird.

11. Compact Drill-Driven Chicken Plucker

Compact Drill-Driven Chicken Plucker

This is a project posted on eBay. The design is a compact drill that saves time and eliminates the unpleasant task of plucking chicken feathers by hand.

The roller is made from a 6-inch PVC pipe about a foot long. Plucking fingers fit and protrude on the outside of the pipe.

The roller is spun using a power drill attached to a carriage bolt. This carriage bolt is what acts as a shaft threaded through end caps on the PVC pipe.

The designer uses a C-clap to hold the drill steady. When you consider the size, this plucker can be used on one bird at a time.

12. Homemade Chicken Plucker with Shower Head

Homemade Chicken Plucker with Shower Head

This machine is built to multitask. The designer wants something that plucks feathers and cleans the bird once done. A shower head is fitted to help achieve that.

Plucking fingers are fitted inside a barrel. This same barrel is used to hold the chicken while de-feathering.

This plucking machine is driven by a motor. The designer does not specify motor size so you can choose one that meets your needs. A waterproof switch ensures the safe working of the machine, even when chicken soup splashes on it.

The machine is framed in wooden boards. Wheels are fitted on the base of the frame to turn it into a mobile de-feathering machine.

13. $14 Fully Mobile Homemade Chicken Plucker

There are three things the designer of this de-feathering machine wants to achieve here. What he wants is an inexpensive, easy to clean, and fully mobile chicken plucker.

Plucking fingers are fitted on a bucket. The designer uses longer fingers at the top so that the chicken doesn’t come flying out. A bicycle rim is used for the pulley system.

The bucket has a hole drilled near the bottom. This hole functions as a drain when hosing down the feathers collected inside the bucket.

There is a slight improvement that the designer wants on this plucking machine. It is a bucket cover that goes down the motor to keep it waterproof.

14. Manual Low-Tech DIY Chicken Plucker

Manual Low-Tech DIY Chicken Plucker

This low-tech machine doesn’t use any motor or drill. Instead, your hand takes the place of the motor or drill.

The designer builds it in the form of a box open on the top and two sides. Plywood is used to make the box lightweight for easy portability.

Plucking fingers are installed on the two upright sides of the box. The chicken is pushed back and forth through the fingers to de-feather.

You will need to do some hand job for finishing touches. The designer likes the fact that it reduces hand plucking time by almost half.

She contemplates making some improvement on this machine. She plans to achieve that by making the walls adjustable. This will help pluck both large and small birds.

15. DIY Chicken Plucker for Less Than $20

DIY Chicken Plucker for Less Than $20

Kate, an avid DIYer builds this inexpensive de-feathering machine. She calls it the $6 chicken plucker, though the cost is a little high.

Her aim is to build something less complicated yet effective for the work. She uses a small section of PVC pipe. The pipe is fitted with a cap on one end.

Kate uses bungee straps instead of store-bought plucking fingers. These are fit are threaded on holes drilled in the PVC pipe.

This plucking machine is mechanically driven by a power drill. Kate says it leaves some feathers but works considerably well.

16. 90-Second Tub-Style Mechanical Plucker

90-Second Tub-Style Mechanical Plucker

DIYer Janet builds this chicken plucking machine. She calls it an inexpensive version of the large Whizbang plucking machine.

It uses the same concept, except that most materials used here are salvaged. A barrel with a cutout bottom fitted with plucking fingers is used. This is driven by a motor.

As the video indicates, this plucker does a good job. It literally leaves no feathers behind to give a clean job in just 90 seconds.

17. Homemade Chicken Plucker Less Than $10

Homemade Chicken Plucker Less Than $10

This is an inexpensive plucking machine that works on a few birds at a time. Well, that is quite recommendable considering its size and what powers it.

To start off, this plucker is powered by nothing more than a power drill. Rubber straps are used as plucking fingers. These are threaded through holes drilled in a PVC pipe.

The drill is tied down on a table and the trigger bound with a wire tie. This gives a no-hands operation on the drill. So it takes just one person to pluck feathers. The machine plucks a bird in 45 seconds.

I hope this article has inspired you to build yourself a plucking machine or two. Please pass the message across by sharing our ideas with family and friends.

Have something to add on? Well, feel free to put it in the comment section below.